(888) 823-5247

Installing Insulation on an Electric Hot Water Heater

Installing an Insulation Blanket on an Electric Water Heater

Note: Installation is more difficult on gas and oil-fired heaters. Ask a qualified HVAC contractor for instructions.

  1. Cut the tank top insulation to fit around the piping in the top of the tank. Tape the cut section closed after the top has been installed.
  2. Fold the corners of the tank top insulation down and tape to the sides of the tank.
  3. Position the insulating blanket around the circumference of the tank. For ease of installation, position the blanket so that the ends do not come together over the access panels in the side of the tank. Some tanks have only one access panel.
  4. Secure the blanket in place with the belts provided. Position the belts so they do not go over the access panels (Figure 2). Belts should fit snugly over the blanket but not compress it more than 15% to 20% of its thickness. The installation is easier with two people. If working alone, use tape to hold the blanket to the top until you get the belts into position.
  5. If your water heater has the temperature/ pressure relief valve and the overflow pipe on the side of the tank instead of on the top, install the blanket so these items are outside of the blanket. Depending on the piping arrangement and location, you may need to compress, or even cut, the blanket.
  6. Locate the four corners of the access panel(s). Make an x-shaped cut in the insulating blanket from corner to corner of each access panel.
  7. Fold the triangular flaps produced by the cuts underneath the insulating blanket. Repeat steps 6 and 7 for the rating/ instruction plate.
  8. The blanket must not be installed on a leaking tank.

© Online-Access

24 Hour Emergency Service • Call Us Today • (888) 823-5247 • or • Fill Out Our Online Form
24 Hour Emergency Service
Call Us Today
(888) 823-5247
Fill Out Our Online Form
Send Us a Message
 
 
Payment Options
 
 
For furnace in Bowie MD, we accept most major credit cards.
We accept cash for heating repair service provided in Crofton MD.
We accept check for heat pump repair service provided in Annapolis MD.
Belair Engineering and Service Company, Inc. accepts all major credit cards, cash, and local, personal checks. We also offer a variety of financing options. Contact us for more information
 
Connect With Us
 
Belair Engineering and Service Company, Inc. is the 2017 Capital Readers Choice Winner!
Contact Information
 
Belair Engineering and Service Company, Inc.
Address:  15881 Commerce Court
 Upper Marlboro, MD 20774
Phone:     (301) 249-0300
Toll Free:  (888) 823-5247
Fax:         (301) 249-0302
Belair Engineering and Service Company, Inc.
Address:  15881 Commerce Court
Upper Marlboro, MD 20774
Phone:     (301) 249-0300
Toll Free:  (888) 823-5247
Fax:          (301) 249-0302
Schedule Service
Home   |   Email Us   |   Schedule Service   |   Get a Quote   |   Ask a Tech   |   Maintenance   |   Employment   |   Privacy Policy
GBCC member, Belair Engineering is the boiler & heat pump repair service in Bowie MD. We are a proud ACCA member, so trust us with your furnace repair service in Annapolis MD. Associated Builders and Contractors for better heat pump and furnace repair service in Bowie MD. Heating and air conditioning contractors in The Crofton Chamber of Commerce; Trust them with your boiler unit repair in Bowie MD. Get a Energy star heat pump installation done by Belair in Bowie MD. Heat Pump & boiler repair service in Bowie MD. Generators & boiler Unit repair service in Crofton MD. Nate member for better heat pump repair service in Crofton MD. Be Eco friendly with a boiler Unit installation in Crofton MD. Lead safe heat pump and furnace repair or installation in Bowie MD. Come see the Gas fireplace inserts & gas fire logs installation in our Bowie MD showroom! Hearth patio & barbecue repair service in Expo in Crofton MD. NCI member to help furnace repair service in Bowie MD. Service Roundtable member; heat pump service and heating repair in Annapolis MD.