(888) 823-5247

Selecting and Maintaining a Sump Pump

Selecting and Maintaining a Sump Pump

If you have a house with a basement or crawl space, you likely have a sump pump. From time to time, these pumps need to be replaced. Knowing what type of pump works best for your situation will keep failures, flooded basements and other hazards to a minimum.

There are two main types of sump pumps: pedestal and submersible. A pedestal type pump has the motor attached to the top of a shaft. The motor is not designed to be under water. A pedestal pump works well in small diameter basins.

Submersible pumps are designed to sit in the base of the sump basin, below water level. These are more adapted to larger sump basins and are typically quieter than pedestal pumps.

Sump pumps usually come with an automatic on/off switch. A float switch is the most common. As the float rises with rising water levels in the basin, the pump is started after the water rises to a certain level.

To determine the size of pump needed you must know how much water will need to be pumped, how high the water will be pumped, and the length and size of pipe. Do not assume that having a large horsepower pump will be the best choice. A large horsepower pump in a small diameter basin will cause the pump to cycle frequently, shortening pump life. At the same time, you need a pump that will keep up with maximum drainage. Pump capacity charts are available through professional installers or pump manufacturers, or they can be found on the web.

When installing a sump pump, it is usually recommended that a check valve be installed. This prevents water left in the outlet pipe from flowing back into the basin. Some valves can be attached to the sump pump itself, while others are placed farther up the outlet pipe. If the valve is not attached to the pump, it is recommended that a 1/8-inch air relief hole be drilled into the outlet pipe, between the valve and the pump. This prevents a condition called an air lock, where the pump will attempt to work but cannot pump water. Be sure the air relief hole is placed so that any water that comes out of the hole will remain in the drainage basin!

A dedicated electrical circuit should be used for the pump. Most pumps have a high amp load when starting. Do not use an extension cord to plug the pump into the outlet.

To maintain a sump pump, periodically check the system. Make sure the float is free of obstructions. Observe the outlet to make sure water is actually being pumped. Listen for unusual noises when the pump is running. If the pump runs just a few months of the year, fill the basin with water and make sure the system is operating before its normal operation time begins.

If a sump pump fails, and water gets into the basement, do not attempt repairs without first turning off the power to all basement outlets. To minimize long term indoor air quality concerns, dry the areas affected as soon as possible. If flooding is severe or long lasting, dry wall, carpeting and other materials may need to be replaced.

If a quality pump is used that is properly sized, it should last three or more years, with 10 years being reasonable, according to the U.S. Department of Housing and Development. When purchasing a pump, look for one that is built and tested according to Sump and Sewage Pump Manufacturers Association (SSPMA) specifications.


Source: University of Illinois
24 Hour Emergency Service • Call Us Today • (888) 823-5247 • or • Fill Out Our Online Form
24 Hour Emergency Service
Call Us Today
(888) 823-5247
Fill Out Our Online Form
Send Us a Message
 
 
Payment Options
 
 
For furnace in Bowie MD, we accept most major credit cards.
We accept cash for heating repair service provided in Crofton MD.
We accept check for heat pump repair service provided in Annapolis MD.
Belair Engineering and Service Company, Inc. accepts all major credit cards, cash, and local, personal checks. We also offer a variety of financing options. Contact us for more information
 
Connect With Us
 
Belair Engineering and Service Company, Inc. is the 2017 Capital Readers Choice Winner!
Contact Information
 
Belair Engineering and Service Company, Inc.
Address:  15881 Commerce Court
 Upper Marlboro, MD 20774
Phone:     (301) 249-0300
Toll Free:  (888) 823-5247
Fax:         (301) 249-0302
Belair Engineering and Service Company, Inc.
Address:  15881 Commerce Court
Upper Marlboro, MD 20774
Phone:     (301) 249-0300
Toll Free:  (888) 823-5247
Fax:          (301) 249-0302
Schedule Service
Home   |   Email Us   |   Schedule Service   |   Get a Quote   |   Ask a Tech   |   Maintenance   |   Employment   |   Privacy Policy
GBCC member, Belair Engineering is the boiler & heat pump repair service in Bowie MD. We are a proud ACCA member, so trust us with your furnace repair service in Annapolis MD. Associated Builders and Contractors for better heat pump and furnace repair service in Bowie MD. Heating and air conditioning contractors in The Crofton Chamber of Commerce; Trust them with your boiler unit repair in Bowie MD. Get a Energy star heat pump installation done by Belair in Bowie MD. Heat Pump & boiler repair service in Bowie MD. Generators & boiler Unit repair service in Crofton MD. Nate member for better heat pump repair service in Crofton MD. Be Eco friendly with a boiler Unit installation in Crofton MD. Lead safe heat pump and furnace repair or installation in Bowie MD. Come see the Gas fireplace inserts & gas fire logs installation in our Bowie MD showroom! Hearth patio & barbecue repair service in Expo in Crofton MD. NCI member to help furnace repair service in Bowie MD. Service Roundtable member; heat pump service and heating repair in Annapolis MD.